Grow Tent and Light Shopping
- Thread starter High kev
- Start date
Punisher84
Just some asshole
Most divers aren’t racist so you can use any color of your choice. I’ve not used that driver myself so it might be racist, not positive though.
sfrigon1
Seed Aficionado
I'm proud of you bro . The spacing is even better than the original! Well done
I’m ready to take over the world nowI'm proud of you bro . The spacing is even better than the original! Well done
Big Terps
Growing on a dime
Yes!! Like my friend @sfrigon1 said great job on this build. This version looks alot better than the first on u had imo. Similar to the one i built. Spacing looks dam good. Like how the 2 in middle are floppd opposite of outers. So good job buddy u came along way. Now grow sum 
with em! Lol.
What was ur measurements? If u are putting that in a 4x4 did u make it like 46 x 46 to give u a little clearance to fit in ur 48x48? Or u just make it the whole 48x48?
Nice job bro!
with em! Lol.What was ur measurements? If u are putting that in a 4x4 did u make it like 46 x 46 to give u a little clearance to fit in ur 48x48? Or u just make it the whole 48x48?
Nice job bro!
sfrigon1
Seed Aficionado
Should it fit that close ? What if u put that in a five by five? Would the six inches around the perimeter matter ?Yes!! Like my friend @sfrigon1 said great job on this build. This version looks alot better than the first on u had imo. Similar to the one i built. Spacing looks dam good. Like how the 2 in middle are floppd opposite of outers. So good job buddy u came along way. Now grow sum
What was ur measurements? If u are putting that in a 4x4 did u make it like 46 x 46 to give u a little clearance to fit in ur 48x48? Or u just make it the whole 48x48?
Nice job bro!
Big Perm
Budtender
The light will spread from the board. 6" around the perimeter would be about perfect for a 5x5, imo.
sfrigon1
Seed Aficionado
Awesome
and that's at like twelve inches? I'm in the process of switching over to QB's just curious
Big Perm
Budtender
I don't know about these boards as far as distance from canopy. Never ran them, myself.Awesome
I did 48 by 48 will be put in a 5 x5 areaYes!! Like my friend @sfrigon1 said great job on this build. This version looks alot better than the first on u had imo. Similar to the one i built. Spacing looks dam good. Like how the 2 in middle are floppd opposite of outers. So good job buddy u came along way. Now grow sum
What was ur measurements? If u are putting that in a 4x4 did u make it like 46 x 46 to give u a little clearance to fit in ur 48x48? Or u just make it the whole 48x48?
Nice job bro!
Glossybudz
Super Active Member
I think the LRS MW driver's run hotter then the HLG driver's.
If you can i would try keep them outside the grow space. Thats only if heats a issue i believe i did read that they run hotter
gwheels
Hobby Farmer
After having a driver out of a tent...any time you can get drivers out of the tent it is better. Then you can pound them with photons and if its too much you know its not a heat problem.
Its too much light.
I think i am going to add wire to all my drivers and get them out of tents. That QB135 for example is always a pain for heat in the 20 x 36 x 62 tent. But if i can wire that driver out of the tent i can turn it up.
Its too much light.
I think i am going to add wire to all my drivers and get them out of tents. That QB135 for example is always a pain for heat in the 20 x 36 x 62 tent. But if i can wire that driver out of the tent i can turn it up.
Bruno8437
Super Active Member
I mounted the LRS driver on the fixture and it runs cool, just a degree or 2 above the room temp. The QB132 run about 10 degrees above the room temp. The fan on the LRS driver really helps the LRS with cooling. The HLG drivers run hotter because they only have passive cooling.I think the LRS MW driver's run hotter then the HLG driver's.
If you can i would try keep them outside the grow space. Thats only if heats a issue i believe i did read that they run hotter
Glossybudz
Super Active Member
Yeah i thought it was one or the other.
Thanks
